{"id":3454,"date":"2026-10-08T09:40:28","date_gmt":"2026-10-08T01:40:28","guid":{"rendered":"http:\/\/www.rsmdailynews.com\/blog\/?p=3454"},"modified":"2026-10-08T09:40:28","modified_gmt":"2026-10-08T01:40:28","slug":"what-are-the-corrosion-prevention-methods-for-data-center-cooling-systems-424f-c69473","status":"publish","type":"post","link":"http:\/\/www.rsmdailynews.com\/blog\/2026\/10\/08\/what-are-the-corrosion-prevention-methods-for-data-center-cooling-systems-424f-c69473\/","title":{"rendered":"What are the corrosion prevention methods for data center cooling systems?"},"content":{"rendered":"

Hey everyone, I\u2019m Mia, and I\u2019ve been working in data center cooling for the better part of 10 years now\u2014mostly with companies running everything from edge facilities to hyperscale campuses. If there\u2019s one problem I\u2019ve fielded more calls about than any other, it\u2019s corrosion in cooling systems. It\u2019s not just an annoying headache, either. Corroded pipes, fouled heat exchangers, and rusted pump parts don\u2019t just raise energy bills (we\u2019re talking 10-15% extra for inefficient heat transfer here)\u2014they also trigger unplanned outages that cost data centers hundreds of thousands of dollars per hour. Over the years, I\u2019ve tested and fine-tuned a handful of prevention methods that actually work, not just the generic stuff you\u2019ll find on Wikipedia. Let\u2019s break this down like we\u2019re sitting in a break room, no stuffy engineering jargon overkill. Data Center Cooling Systems<\/a><\/p>\n

<\/p>\n

First, let\u2019s get on the same page about why corrosion even happens in data center cooling systems. These systems are closed-loop most of the time, but they\u2019re not airtight\u2014they breathe a little, pick up tiny amounts of oxygen from makeup water, and run warm 24\/7, which accelerates chemical reactions. The worst offenders? Usually carbon steel pipes (super common because they\u2019re cheap and strong, but terrible with water) and copper heat exchangers (great for heat transfer, but prone to pitting when exposed to certain metals or chemicals). Oh, and if you\u2019re using a closed-loop system with glycol for freeze protection? Glycol breaks down over time into acidic compounds, which eat away at metal way faster than plain water. I\u2019ve seen a system go from pristine to leaking in 18 months just because no one monitored glycol degradation.<\/p>\n

Now, let\u2019s get to the good stuff: the actual prevention methods I swear by, and that our team at the cooling supply firm I work with has installed and refined for clients across the US. Let\u2019s start with the most basic (and often overlooked) one: water quality management. A lot of people just top off systems with tap water and call it a day. Big mistake. Tap water has all kinds of junk that causes corrosion\u2014dissolved minerals (calcium, magnesium, iron), chlorine, and oxygen. For closed-loop systems, you need to use deionized (DI) water or reverse osmosis (RO) water for makeup. I remember a mid-sized colocation client who had massive rust issues in their pipework; we switched them to RO water for all makeup points, and their corrosion rate dropped by 70% within 6 months. That\u2019s not a stat pulled from a white paper\u2014that\u2019s real client data. But it\u2019s not just about the makeup water; you have to test the system water monthly for pH, conductivity, and oxygen levels. The sweet spot for pH in closed-loop systems is 8.2 to 8.8\u2014too low (acidic) and metal eats away, too high (alkaline) and you get scaling that clogs pipes. We also teach clients to keep dissolved oxygen levels below 0.5 ppm; any higher and you\u2019re basically feeding corrosion. Some facilities add oxygen scavengers, right stuff like sodium sulfite or isoascorbic acid, but you have to dose them correctly\u2014too little and they don\u2019t work, too much and they can react with other chemicals and cause foaming in heat exchangers.<\/p>\n

Next up: material selection. This is where a lot of new data centers cut corners, trying to save a buck on pipe materials, and end up paying for it three years later. Carbon steel pipes are the go-to for budget projects, but they need a protective lining to avoid corrosion. Epoxy linings are the most common, but not all epoxies are equal. We tested a cheap epoxy lining a client got from a random supplier\u2014 it started peeling in 2 years, and under the peeling spots, the pipe was rusted through. Now we only use fusion-bonded epoxy (FBE) linings; they\u2019re baked on at high temps, so they stick way better and resist chipping from system pressure changes. If you can swing the cost, stainless steel pipe is worth every penny. Type 316 stainless is even better than 304 because it has more molybdenum, which makes it resistant to pitting from chlorides. We recently worked with a hyperscale client that switched from 304 to 316 on their cold water headers, and their corrosion monitoring probes stopped showing any active rust after a year. Another thing: avoid mixing metals in your system. If you have a copper heat exchanger connected to a carbon steel pipe, you get galvanic corrosion\u2014two different metals touching in water creates a tiny electrical current that eats away the less noble metal (usually steel). The fix here is to install dielectric fittings between dissimilar metals to break that electrical path. Simple, cheap, and it works wonders.<\/p>\n

Then there\u2019s chemical treatment, which is like the guardrails for your system. A lot of people think of corrosion inhibitors as optional add-ons, but they\u2019re non-negotiable for any cooling system running longer than a year. The right inhibitors form a thin, invisible protective layer on metal surfaces, keeping water and oxygen from touching the metal itself. There are a couple types: for steel pipes, we use film-forming inhibitors like orthophosphates or polyphosphates\u2014they coat the entire interior of the pipe, not just cover a spot. For copper components, we add azole-based inhibitors, like benzotriazole (BTA) or tolyltriazole (TTA)\u2014these form a protective barrier that stops copper from pitting. Pro tip for glycol systems: if you use propylene glycol (the non-toxic kind, common for data centers that handle sensitive equipment), make sure your inhibitor package is compatible with glycol. Some inhibitors only work with water, and mixing them with glycol leads to wasted product and no corrosion protection. Also, you have to test inhibitor concentrations quarterly\u2014they get used up over time, especially at higher operating temps. I had a client once skip quarterly testing because \u201cit\u2019s working fine now,\u201d and by the time they checked, the inhibitor level was 50% too low, and their heat exchanger had corroded so bad it needed to be replaced early. Ouch.<\/p>\n

Another method that\u2019s gaining traction (and we\u2019ve installed this at a few high-security data centers) is cathodic protection. This is more for large systems, like those with miles of underground pipes or large cooling tanks. Let\u2019s keep this simple: corrosion is basically metal losing electrons, so cathodic protection forces the pipe to gain electrons instead, making it the cathode (unaffected) instead of the anode (corroding). There are two types: impressed current and sacrificial anode. Sacrificial anodes are simpler\u2014you attach pieces of a more reactive metal, like magnesium or zinc, to the pipe. The anode corrodes instead of the pipe. Impressed current uses a small power source to push electrons into the system, good for bigger, harder-to-reach systems. We recently did a retrofit for a 10-megawatt data center that had constant corrosion in their underground water pipes; adding sacrificial magnesium anodes cut their corrosion rate by 85% and they haven\u2019t had a leak in two years. The only catch is you have to replace the anodes every 3-5 years, but that\u2019s way cheaper than replacing a pipe.<\/p>\n

Wait, can\u2019t forget about regular maintenance and monitoring, right? I\u2019ve seen too many data centers install all the right stuff, then forget to check it for years. There are cheap, easy ways to track corrosion without tearing apart pipes. Corrosion monitoring probes\u2014small metal cylinders made of the same material as your pipes\u2014installed in the system. You pull them out every 6 months, weigh them, and calculate the corrosion rate. If you\u2019re seeing more than 0.1 mpy (mils per year), that\u2019s a red flag. We also recommend doing annual water quality audits by a specialist\u2014someone who knows data center systems, not just a general plumber. And don\u2019t sleep on flushing the system every 3-5 years. Over time, sludge and rust accumulate at the bottom of pipes and heat exchangers, which insulates the metal and makes inhibitors less effective. A good flush (using neutral chemicals, not harsh acids that can damage metal) can bring a system back to like-new condition. I had a client who\u2019d gone 7 years without a flush, their heat exchanger efficiency was down 12% because of sludge. We flushed it, added fresh inhibitors, and efficiency jumped back to 98% within a month\u2014plus no more signs of corrosion.<\/p>\n

<\/p>\n

Now, let\u2019s talk about what we usually warn clients to avoid, because a lot of bad practices come from trying to save a buck. First, don\u2019t overchlorinate for system sanitization. Chlorine is great for killing bacteria, but it\u2019s a major cause of copper pitting and steel corrosion. If you need to sanitize a system, use something like hydrogen peroxide or peracetic acid\u2014they\u2019re gentler and don\u2019t leave corrosive residues. Second, don\u2019t ignore makeup water line leaks. A tiny leak in a makeup line that\u2019s adding raw tap water to your system is dumping all that chlorine and minerals right into your closed loop. Third, don\u2019t mix different brands of inhibitors or glycol. Each brand\u2019s package is formulated to work with their own product, and mixing can cause chemical reactions that form sludge or neutralize inhibitors. We\u2019ve had a few clients call us panicking after mixing two inhibitors from different suppliers\u2014turns out they\u2019d caused a precipitate that was clogging their heat exchanger tubes, and we had to flush the whole system at a big cost.<\/p>\n

Integrated Cooling System<\/a> Here\u2019s the thing: corrosion isn\u2019t an inevitable part of running a data center cooling system. I\u2019ve seen systems that have been running for 15 years with zero major corrosion issues, all because they stuck to consistent, science-backed practices. At our company, we don\u2019t just sell parts or chemicals\u2014we work with clients to build a custom corrosion prevention plan, based on their system size, operating temps, and equipment types. Whether you\u2019re a small edge data center with a 10-ton chiller or a hyperscale facility with 100+ cooling units, there\u2019s a solution that fits your budget and needs. If you\u2019re dealing with rusty pipes, high energy bills, or unplanned outages from corrosion, we\u2019d love to walk through your setup, answer any questions, and help you put a plan in place to stop it before it gets worse.<\/p>\n

References<\/h2>\n